Locksmith in Sawlog Bay, OntarioChange the locks,keep the peace of mind
Sometimes the honest answer is a full lock change: a cylinder that fights every key, a handle set that no longer matches the door, a break-up where rekeying feels like half a measure. For homes across Sawlog Bay we replace the hardware, match the finish to what is already on the house and hand over new keys.
Commercial customers in Sawlog Bay get a locksmith who understands traffic. A storefront door swings hundreds of times a day, and hardware chosen for a house will not last on it. We fit closers, lever sets and exit devices built for that use, adjust them so the door latches on its own, and schedule a service visit before anything wears out.
— Wasaga Beach Lock Services
A locksmith who listensThe job starts with your description, not our assumptions. What you have noticed about the door often points to the cause before we touch it.
Honest about what is worth doingSome hardware deserves saving and some does not. We tell you which and why, so you spend on what makes a difference.
Left better than foundThe door works, the area is clean and you have keys, notes and a clear idea of what to watch for. That is the standard for every visit.
Hours
HoursOpen 24/7
Nights and weekendsSame fees
In business16 years
VisitsOn-site assessment
Locksmith services
What we can sort out
These are the services we bring to doors across Sawlog Bay. Residential work covers lockouts, rekeying, lock replacement, deadbolts, smart locks and older hardware brought back to life. Commercial work covers storefront doors, exit devices, closers, master keys and safes. Vehicle key cutting rounds out the list when it is needed.
The commercial pages cover the hardware and keying behind a working premises: business lockouts, rekeying after staff changes, master key design, heavy-duty replacement locks, panic and exit devices, access control with codes or cards, and safes for cash and records.
Getting in is only half of an emergency visit. Once the door is open we look at why it locked you out: a worn key, a failing cylinder, a latch that catches.
About 47% of homes in Tiny were built in 1980 or earlier, according to the 2021 Census.
In an area where homes span several eras, one street may have original mortise locks and the next builder-grade cylinders. A locksmith working here carries parts for both, so whichever door he meets, the job finishes in one visit.
97%Mostly houses
Single-detached houses make up about 97% of homes in Tiny (2021 Census).
A detached house gives a locksmith room to work: full access to both sides of every door, hinges and frames included. Repairs and upgrades can be thorough, from the front deadbolt to the gate latch, with nothing off limits.
The intruder pried open our sliding patio door. Can it be made secure?
Yes. The panel goes back on its track and the broken latch is replaced, then the weaknesses a slider is born with are addressed: anti-lift blocks in the upper channel so the panel cannot be raised off its rollers, a foot bolt or pin lock through the frame at the bottom, and an auxiliary keyed lock if the latch alone is flimsy. A bowed frame may need a door installer, with the opening secured until they come.
Is a key stuck in the lock the same problem as a jammed lock?
They are close relatives. A key that will not come out is usually a plug that has not returned to its neutral position with the shell, a cylinder cap that has loosened, debris in the keyway, or a cylinder that is pinned incorrectly; some cylinders are also designed to hold the key until the plug is returned. The locksmith frees the key first, without pulling, then treats the cause the same way as any seized cylinder.
How long does a whole-house rekey take?
Plan on an hour or two for a typical house with three or four cylinders, including the walk-through, identification, pinning, cutting and testing. Each additional cylinder adds a little, as does swapping a cylinder to bring a mismatched door onto the same key, resetting a homeowner-rekeyable lock or clearing a garage opener. The locksmith gives a realistic window on the phone once the list of doors is known.
Is it worth repairing an old mortise lock instead of replacing it?
Usually, yes. The mechanisms are simple and robust, and what fails is nearly always a spring, dried grease or wear on one part, all of which are repairable on a bench. Replacing the lock with a modern cylindrical set means boring a large hole through the door stile and filling the old pocket, which is more work and changes the door for good. A rebuilt case keeps the original trim and keeps the door intact.
How do I know what brand or type of lock is on my mailbox?
You generally do not need to; identifying the hardware is part of the visit. The locksmith reads the maker's mark on the lock face, measures the cylinder and cam, and checks the hole pattern in the compartment door, which together point to a matching replacement even when the original brand is no longer sold.